ENGLISH ESPAÑOL International Assembly Instructions for model JFA36 FRANÇAIS ITALIANO (6901-300106 <00>) Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 USA Customer Service: (800) 359-5520 · (651) 484-7988 · fax (651) 636-0367 Customer Service Europe: +31 - (0)40 26 68 619 · fax +31 - (0)40 26 68 615 See complementary Sanus products at www.sanus.com ENGLISH Assembly Instructions for Model: JFA36 Thank you for choosing the Java Furniture line from Sanus Systems. Safety Warning: If you do not understand these directions, or have any doubts about the safety of the installation, please call a qualified contractor or contact Sanus at 800.359.5520 or www.sanus.com. Check carefully to make sure that there are no missing or defective parts. Our customer service representatives can quickly assist you with installation questions and missing or damaged parts. Replacement parts for products purchased through authorized dealers will be shipped directly to you. Never use defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified by Sanus Systems. Sanus Systems can not be liable for damage or injury caused by incorrect mounting, incorrect assembly, or incorrect use. Please call Sanus Systems before returning products to the point of purchase. Required Tools: Phillips screw driver, hammer or mallet (optional) Supplied Parts and Hardware: Some parts not shown as actual size* (14) Cam Pin - b (14) Cam - a (18) Dowel - c (8) M6 Bolt - d (8) Rubber Spacer - e (8) Aluminum Spacer - f (4) Base Bolt - g (8) Carpet Glide - h (16) Back Panel Screw - i (1) Allen Key - j* (12) Shelf Pin - k (12) Shelf Pin Screw - l (1) Door Latch - m (4) Latch Screw - n Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 USA Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com Parts: ENGLISH (1) Top - o (1) Bottom - p (2) Main Base Rail - q (2) Side Base Rail - r (1) Left Side Panel - s (1) Right Side Panel - t (1) Door - u (2) Leg - v (3) Shelf - x (2) Back Panel - w Step 1: Add Cam Pins and Dowels to Base Thread a Cam Pin (b) into each threaded hole and insert a Dowel (c) into each adjacent hole in the Bottom (p). Tighten each with a Phillips screw driver. See Diagram 1 for assistance. Diagram 1 Detailed View ENGLISH b c p Step 2: Add Side Panels Orient the Side Panels (s,t) so the notch is facing the ground and the shelf holes are facing each other. Insert a Dowel (c) into each hole (closest to the center in the bottom of each Side Panel). Insert a Base Bolt (g) through the Bottom (p) and into each Side Panel. Tighten each Base Bolt with the Allen Key (j). See Diagram 2 for Assistance. Diagram 2 s t c g p notch Step 3: Base Assembly ENGLISH Insert 10 Cams (a), four Cam Pins (b) and four Dowels (c) into the Main Base Rail (q) and Side Base Rail (r). Tighten each Cam Pin with a Phillips screw driver. Make sure the arrow on each Cam is pointed toward the closest hole. Press fit each rail together until a solid rectangle is formed. Tighten each Cam that corresponds with a Cam Pin in a clockwise motion to secure the Rails together. See Diagram 3 for assistance. Diagram 3 r c a q b Step 4: Add Base Assembly to Bottom Align the assembled base frame so the holes line up with the Dowels (c) and Cam Pins (b) on the Bottom (p). Proceed to tighten all six of the Cams (a) on the Rails (q,r) that correspond with the Cam Pins on the Bottom so the assembled base frame is secure. See Diagram 4 for Assistance. Diagram 4 c b p q r a Step 5: Add Carpet Glides ENGLISH Gently tap the Carpet Glides (h) into each frame assembly. See Diagram 5 for Assistance. Diagram 5 Detailed View h Step 6: Add Door Latch Attach the Door Latch (m) to the Top (o) with the four Latch Screws (n). Tighten each Latch Screw with a Phillips screw driver. See Diagram 6 for assistance. Diagram 6 Detailed View o m n Step 7: Prepare Top ENGLISH Insert a Cam Pin (b) into each threaded hole and insert a Dowel (c) into each adjacent hole in the Top (o). Tighten each Cam Pin with a Phillips screw driver. See Diagram 7 for assistance. Diagram 7 Detailed View c o b Step 8: Add Door and Top Gently position the cabinet assembly so it is up-right and resting on the base. Insert a Cam (a) into each Side Panel (s,t). Make sure the arrow on each Cam points toward the appropriate Cam Pin in the Top (o). Insert the Door (u) into the base so the pivot side is opposite from the Door Latch (m). Fit the Top onto the Side Panels so the Cam Pins correspond with the Cams and the Door is secured in the top. Tighten each Cam in a clockwise motion. See the Diagrams below for assistance. Detailed View View from Front View from Back pivotpoint notch a o u Step 9: Add Legs To add the Legs (v) first slide the Rubber Spacer (e) so it fits into the Aluminum Spacer (f). Take a M6 Bolt (d) and insert it through the Side Panel (s,t), the Spacer Assembly and finally thread it into the Leg. Repeat this process for the remaining holes on each leg. Tighten each M6 Bolt with the Allen Key (j). See Diagram 9 for assistance. Diagram 9 ENGLISH v f e d Step 10: Install Shelves Insert a Shelf Pin Screw (l) through a Shelf Pin (k) and into the desired hole in the Side Panel (s,t). Tighten with a Phillips screw driver. Repeat process until all 12 Shelf Pins are installed. See the Detailed View of Diagram 10 for assistance. Place each Shelf (x) in cabinet so they fit on top of the Shelf Pins. Press down firmly until it locks into place. See Diagram 10 for assistance. Detailed View Diagram 10 x l k backofcabinetassembly Step 11: Add Back Panels ENGLISH Insert a Back Panel Screw (i) through the Back Panel (w) and into the cabinet assembly in the locations shown in Diagram 11. Tighten each Back Panel Screw with a Phillips screw driver. Repeat process for the other Back Panel. Diagram 11 i w Note: Sanus recommends placing components and completing all necessary wire and cable hook-ups before attaching the Back Panels. Complete Assembly Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 USA Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com LA UNIÓN DE FORMA Y FUNCIÓN Instrucciones de ensamblaje del modelo: JFA36 Gracias por elegir la línea de muebles Java de Sanus Systems. Advertencia de seguridad: Si no entiende estas instrucciones o si tiene alguna duda con respecto a la seguridad de la instalación, llame a un contratista cualificado o comuníquese con Sanus llamando al 800.359.5520 (en EE.UU.) o al 31 (0) 40 2668619 (en Europa). Puede también visitar nuestro sitio web en www.sanus.com. Revise cuidadosamente los productos para asegurarse de que ninguna pieza falte ni presente defectos. Nuestros representantes del servicio de atención al cliente le ofrecerán asistencia inmediata con cualquier duda sobre la instalación o con respecto a piezas faltantes o dañadas. Las piezas de repuesto para los productos comprados a través de un distribuidor autorizado se enviarán directamente a usted. Nunca use piezas defectuosas. La instalación incorrecta podría ocasionar daños o lesiones graves. No utilice este producto para fines no explícitamente especificados por Sanus Systems. Sanus Systems no será responsable por daños ni lesiones debidos al montaje, ensamblaje o uso incorrectos. Llame a Sanus Systems antes de devolver los productos al punto de compra. Herramientas necesarias: Destornillador Phillips, martillo o mazo (optativo) Piezas y tornillería suministradas: Algunas piezas no se muestran en tamaño real* ESPAÑOL (14) Leva - a (14) Pasador de leva - b (18) Espiga - c (8) Perno M6 - d (8) Espaciador de goma - e (8) Espaciador de aluminio - f (4) Perno de base - g (8) Deslizador para alfombra - h (16) Tornillo de panel trasero - i (1) Llave allen - j* (12) Pasador de apoyo de repisa - k (12) Tornillo de pasador de apoyo repisa - l (1) Seguro de puerta - m (4) Tornillo de seguro de puerta - n Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 USA Servicio de atención al cliente: 800.359.5520. Vea los productos complementarios de Sanus en el sitio www.sanus.com Piezas: ESPAÑOL (1) Plancha superior - o (1) Plancha inferior - p (2) Tabla principal de base - q (2) Tabla lateral de base - r (1) Panel lateral izquierdo - s (1) Panel lateral derecho - t (1) Puerta - u (2) Pata - v (3) Repisa - x (2) Panel trasero - w Paso 1: Adición de los pasadores de leva y espigas a la base Enrosque un pasador de leva (b) en cada agujero roscado e inserte una espiga (c) en cada agujero adyacente de la plancha inferior (p). Apriételos todos con un destornillador Phillips. Vea el diagrama 1 como ayuda. Diagrama 1 Vista detallada ESPAÑOL b c p Paso 2: Adición de los paneles laterales Oriente los paneles laterales (s,t) de forma tal que la muesca quede hacia el piso y los agujeros queden frente a frente. Inserte una espiga (c) en cada agujero (el más cercano al centro en la parte inferior de cada panel lateral). Inserte un perno de base (g) a través de la plancha inferior (p) y luego en cada panel lateral. Apriete cada perno de base con una llave allen (j). Vea el diagrama 2 como ayuda. Diagrama 2 s t c g ...