CP-ST100 Thank you for buying this Pioneer product. Please read through these operating instructions for proper assembly and use. After you have finished reading the instructions, put them away in a safe place for future reference. Confirm your Accessories · Supports (long) x 2 · Caps x 2 Assembly Hints These stands have been designed to allow the mounting of up to three speakers each, but the number actually mounted will depend on the speaker system used (surround setting). When assembling the stands, use only that number of support arms actually required for the speakers to be mounted. · For more information regarding various surround setups, consult the owners manuals furnished with your speakers and home theater system. Setup examples: · Supports (short) x 4 · Arms x 6 · Front surround setup (using dual center speakers) Front left Surround left Center Front right Surround right Center · Stand bases x 2 · Angle brackets x 6 · Screws (Flat countersunk head, M4xL6), for assembling supports x 16 · Pad gaskets x 6 Listening position · Screws (Bind head, M4xL8), for assembling arms x 6 · Front surround setup Front left Surround left Front right Surround right · Wire clips x 6 · Screws (Bind head, M5xL10) for mounting speakers x 6 · These operating instructions Before you start Center Before setting up your speaker system, we recommend reading the operating instructions for your system thoroughly. Listening position Caution · This stand has been designed to support weights up to 1.1 kg per arm, or a maximum of 3.3 kg (when 3 arms are used). Exceeding these limits may result in falling or breakage. Front right · Standard surround setup (using dual center speakers) Front left Center Surround left Surround right · Only use the screws supplied when fixing the speaker to the speaker stand. Speakers may fall and incur damages if not fixed in place properly. · Do not use with any speaker system other than the one for which the unit was designed. The stand may collapse and be damaged and/or the speaker may fall and cause injury. · Be careful when assembling and moving the speaker stand, as it may cause damage or injury in the event of a fall. · Placing the stand on an unstable surface can be dangerous. Be sure to place it on a flat, firm surface. Listening position · Standard surround setup Front left Front right · Make sure you assemble the stand on a flat surface that is relatively soft (such as a carpet). · Do not sit or stand on the speaker, or let children play on the speaker. Doing so could provoke the speaker to fall, causing damages or bodily injury. Surround left Center Surround right Listening position 2 En · Additional stands will be required if they are used to support surround (rear) speakers as well. Assembling the speaker stands Caution · Pioneer is not responsible for any accidents or damage that result from improper installation, misuse or modification of the product, or natural disasters. Assemble the speaker stands as illustrated below. Please note that a medium-sized Phillips screwdriver is required for assembly. The accompanying illustration shows the fully assembled speaker stand, without speakers or wires. Angle brackets Cap Fasten the angle bracket to the speaker. Orient the gasket material with the rear surface of the speaker, and align the screw hole in the angle bracket with the speaker's screw hole, then use the furnished screw (M5xL10) to securely fasten the angle bracket to the speaker. · In the event the speaker is furnished with two screw holes, fasten the angle bracket to the upper of the two holes. · The angle bracket has been originally designed to be mounted with the rounded angle arm oriented upwards, but in the event interference occurs with speaker terminals, the rounded angle arm may also be mounted downward. Speaker Installation Examples Arms Supports (short) (In the event of interference between speaker terminals and angle bracket) Support (long) 3 Place a support (long) over the mounting post in the stand base, and fasten securely with two countersunk screws (M4xL6). Stand base · The screw holes in the stand base are oriented to the rear side. · The support (long) is designed with specific up-down orientation. Confirm the orientation before assembling. 1 Fasten the wire clips to the arms. Peel the protective paper backing from the clip and affix the clip to the indentation on the underside of the arm as shown. 2 Fasten angle brackets to speakers. Peel the protective paper backing from the gasket and affix the gasket to the angle bracket as shown. · Affix the gasket to the square surface of the angle bracket. Be sure to confirm the direction of the gasket so as to properly align the gasket's hole with the screw hole in the angle bracket. 4 Lay the stand on its side, and pass the speaker wires into the hole in the stand base and through the support. Consult the owner's manual for the speaker system and confirm the proper wires to be used (wires may be color coded). 3 En 5 Assemble the arm and support (short) and pass each speaker wire through in order as shown. · The arms are designed with specific up-down orientation; confirm that the side with the wire clip is oriented downward during assembly. Pass the appropriate speaker wire through each arm and mount the assembled arms in order on the long support. In the case of the speaker wire for the lowest arm, do not pass the wire through the arm, but allow the wire to exit the cutaway portion of the arm as shown, then affix a cap to the top of the arm. Assemble the stands so that the screw holes in the supports are all oriented toward the rear side of the stand, then insert the furnished countersunk screws and tighten securely. Caution · Do not attempt to insert screws when the supports holes are oriented at a diagonal angle from the rear of the stand. Place cap on top of uppermost arm. · Do not attempt to use more than three arms on a single stand, since the stand may fall and cause damage or injuries. 6 Decide on the directional orientation for each speaker, then fix in place with the furnished countersunk screws. · Each arm can mounted facing forward, or pointing 60° to right or left. If a lower speaker unit has an upward-pointing speaker, orient its direction away from the speaker above it. When fixing the speakers in place, also consult the section "Assembly Hints" on page 2. Examples of stand with mounted speakers 4 En 7 Fasten the speakers to the arms. Be sure the speakers are oriented toward the listening position when fastening in place. Specifications External dimensions (largest assembly) ............................300 mm (W) x 1113 mm (H) x 300 mm (D) Weight (largest assembly).................................................. 5.8 kg Supplied accessories Stand bases [SXG1187] .............................................................. 2 Supports (long) [SNH1102] ........................................................ 2 Supports (short) [SNH1098]....................................................... 4 Caps [SXG1198]........................................................................... 2 Arms [SNH1099] ......................................................................... 6 Angle brackets [SNA1511] ......................................................... 6 Wire clips [SEP1381] .................................................................. 6 Pad gaskets [SEB1341]............................................................... 6 Screws (Flat countersunk head, M4xL6) [SBA1303].............. 16 Screws (Bind head, M4xL8) [SBA1304]..................................... 6 Screws (Bind head, M5xL10) [SBA1305]................................... 6 Operating instructions [SRD1366] ............................................ 1 Listening position Align the screw holes in the arm and angle bracket, and use the furnished bind head screws (M4xL8) to fasten securely. Replacement part numbers Non-skid pads [SEB1343] Screws (Bind head, M4xL12) [BPZ40P120FTB] Screws (Bind head, M4xL8) [BMZ40P080FTB] Polyethylene bag S2 [SHL1295] Polyethylene bag S0 [SHL1314] Polyethylene bag S0 [SHL1329] Polyethylene bag S3 [SHL1429] Polyethylene bag S0 [SHL1438] Polyethylene bag S4 [SHL1457] Polyethylene bag S0 [SHL1478] Protection sheet [SHC1844] After fastening the speakers to the arms, attach each speaker wire to its terminal on the rear of the speaker. Use the wire clips to hold the wires in place as required. Protector (Top) [SHA2633] Protector (Bottom) [SHA2634] Packing case [SHG2832] The product numbers are listed above in square brackets. · Specifications and design subject to possible modification without notice, due to improvements. If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling. Private households in the member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to designated collection facilities or to a retailer (if you purchase a similar new one). For countries not mentioned above, please contact your local authorities for the correct method of disposal. By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health. Stand maintenance With normal use, wiping with a soft cloth should be sufficient to keep the stand clean. If necessary, clean with a cloth dipped in a neutral cleanser diluted five or six times with water, and wrung out well. Do not use furniture wax or cleansers. Never use alcohol, thinners, benzine, insecticide sprays or other chemicals on or near this unit since these will corrode the surfaces. When using chemically-treated cloths, be sure to carefully read their accompanying instruction manual. Published by Pioneer Corporation. Copyright © 2008 Pioneer Corporation. All rights reserved. 5 En Nous vous remercions pour l'achat de ce produit Pioneer. Veuillez lire attentivement ce mode d'emploi pour assembler et utiliser correctement ce produit. Après avoir lu ces instructions, rangezles dans un endroit sûr pour pouvoir vous y référer à l'avenir. Vérifiez vos accessoires · Supports (longs) x 2 · Capuchons x 2 Conseils d'assemblage Ces socles ont été conçus pour permettre le montage d'un maximum de trois enceintes chacun, mais le nombre réel d'enceintes montées dépendra du système d'enceintes utilisé (réglages Surround). Lors de l'assemblage des socles, utilisez uniquement le nombre de bras réellement nécessaire pour les enceintes à monter. · Pour en savoir plus sur les diverses installations Surround, consultez les modes d'emploi fournis avec vos enceintes et votre système de cinéma maison. Exemples d'installation: · Bases de socle x 2 · Supports (courts) x 4 · Bras x 6 · Installation Surround avant (utilisation de deux enceintes centrales) Avant gauche Surround gauche Centre Avant droit Surround droit Centre · Supports d'angle x 6 · Vis (tête fraisée plate, M4xL6), pour l'assemblage des supports x 16 · Joints x 6 Position d'écoute · Vis (tête intégrée, M4xL8) pour l'assemblage des bras x 6 · Installation Surround avant Avant gauche Avant droit Surround Surround droit gauche · Serre-fils x 6 · Vis (tête intégrée, M5xL10) pour le montage des enceintes x 6 · Ce mode d'emploi Avant de commencer Centre Avant d'installer votre système d'enceintes, nous recommandons que vous lisiez attentivement le mode d'emploi de votre système. Position d'écoute · Installation Surround standard (utilisation de deux enceintes centrales) Avant gauche Centre Surround gauche Surround droit Avant droit Attention · Ce socle a été conçu pour supporter une masse d'un maximum de 1,1 kg par bras, ou un maximum de 3,3 kg (quand les 3 bras sont utilisés). Dépasser ces limites peut entraîner une chute ou des dommages. · Lors de la fixation de l'enceinte sur le socle d'enceinte, utilisez uniquement les vis fournies. Les enceintes risquent de tomber et de causer des dommages si elles ne sont pas fixées correctement. · N'utilisez pas ce socle avec un autre système d'enceintes que celui pour lequel il a été conçu. Le socle risque de s'effondre et d'être endommagé et les enceintes peuvent tomber et causer des blessures. · Faites attention lors de l'assemblage et du déplacement des enceintes car en cas de chute elles peuvent causer des dommages ou des blessures. · Placer le socle sur une surface instable peut être dangereux. Assurez-vous de le placer sur une surface plate et solide. · Assurez-vous d'assembler le socle sur une surface plage relativement douce (comme sur un tapis). · Ne vous asseyez pas ni ne montez sur une enceinte et ne laissez pas des enfants j ...