KVT-725DVD KVT-725DVD-B MONITOR WITH DVD RECEIVER INSTALLATION MANUAL MONITEUR AVEC RÉCEPTEUR DVD MANUEL D'INSTALLATION MONITOR MIT DVD RECEIVER INSTALLATION-HANDBUCH MONITOR MET DVD-ONTVANGER INSTALLATIE HANDLEIDING MONITOR CON RICEVITORE DVD MANUALE DI INSTALLAZIONE MONITOR CON RECEPTOR DVD MANUAL DE INSTALACIÓN MONITOR COM RECEPTOR DVD MANUAL DE INSTALAÇÃO © PRINTED IN JAPAN B54-4435-00/00 (E)(AI) Before Installation Accessories English 1 ..........1 7 ..........4 2 ..........1 8 ..........4 3 ..........1 9 ..........2 4 ..........1 0 ..........1 5 ..........1 6 ..........2 2CAUTION The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above. 2 English Installation Procedure 1. To prevent a short circuit, remove the key from the ignition and disconnect the - battery. 2. Make the proper input and output wire connections for each unit. 3. Connect the speaker wires of the wiring harness. 4. Connect the wiring harness wires in the following order: ground, battery, ignition. 5. Connect the wiring harness connector to the unit. 6. Install the unit in your car. 7. Reconnect the - battery. 8. Press the reset button. 2WARNING If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. 2CAUTION · If your car's ignition does not have an ACC position, connect the ignition wires to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source with a constant voltage supply, as with battery wires, the battery may die. · If the console has a lid, make sure to install the unit so that the faceplate will not hit the lid when closing and opening. · If the fuse blows, first make sure the wires aren't touching to cause a short circuit, then replace the old fuse with one with the same rating. · Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals. · Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the - wires or ground them to any metal part in the car. · When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). For example, if you connect the + connector of the left speaker to a front output terminal, do not connect the - connector to a rear output terminal. · After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly. · Mount the unit so that the mounting angle is 30° or less. English 3 Connection 2WARNING If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. Battery 4 English + English Monitor unit Do not connect. Steering remote control input (Light Blue/Yellow) REMO.CONT Wiring harness (Accessory 3) Connect to the vehicle's parking brake detection switch harness using the supplied relay connector. 2CAUTION For the sake of safety, be sure to connect the parking sensor. PRK SW D B A Ground Cable (Black) - (To car chassis) ( 5A ) Battery Cable (Yellow) BATT Ignition Cable (Red) ACC Accessory 2 Accessory 0 Accessory 4 FM/AM antenna input Ignition key switch ACC Connector A 8 7 6 5 6 5 4 3 4 3 2 1 2 1 Battery cable (Yellow) Ignition cable (Red) B A D (10A) Car fuse box (Main fuse) Car fuse box 8 7 + ­ C Connector B (Black) Receiver unit (front side) PREOUT TO TV TUNER I/F TO NAVIGATION I/F TO 5L-I/F Disc Changer etc. Cable (included in the disc changer) Receiver unit (rear side) POWER TO MONITOR I/F AV INPUT FM /AM AV OUTPUT ANTENNA Wiring harness (Accessory 1) NOTE If no connections are made, do not let the cable come out from the tab. Power control/ Motor antenna control cable (Blue/White) ANT CONT P.CONT Connect either to the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle. Mute cable (Brown) MUTE Connect to the terminal that is grounded when either the telephone rings or during conversation. NOTE To connect the KENWOOD navigation system, consult your navigation manual. External amplifier control cable (Pink / Black) EXT.CONT To "EXT. AMP. CONT." terminal of the amplifier having the external amp control function. Ground cable (Black) - (To car chassis) C English 5 Connection Connecting the ISO Connector English 2CAUTION The pin arrangement for the ISO connectors depends on the type of vehicle you drive. Make sure to make the proper connections to prevent damage to the unit. The default connection for the wiring harness is described in 1 below. If the ISO connector pins are set as described in 2 or 3, make the connection as illustrated. Please be sure to reconnect the cable as shown 2 below to install this unit to the Volkswagen vehicles etc. 1 (Default setting) The A-7 pin (red) of the vehicle's ISO connector is linked with the ignition, and the A-4 pin (yellow) is connected to the constant power supply. Unit Ignition wire (Red) Battery wire (Yellow) Vehicle A­7 Pin (Red) A­4 Pin (Yellow) 2 The A-7 pin (red) of the vehicle's ISO connector is connected to the constant power supply, and the A-4 pin (yellow) is linked to the ignition. Unit Ignition wire (Red) Battery wire (Yellow) Vehicle A­7 Pin (Red) A­4 Pin (Yellow) 3 The A-4 pin (yellow) of the vehicle's ISO connector is not connected to anything, while the A-7 pin (red) is connected to the constant power supply (or both the A-7 (red) and A-4 (yellow) pins are connected to the constant power supply). Unit Ignition wire (Red) Vehicle A­7 Pin (Red) Connect to a power source that can be turned on and off with the ignition key. Battery wire (Yellow) Connector Function Guide Pin Numbers for ISO Connectors External Power Connector A­4 A­5 A­7 A­8 Speaker Connector B­1 B­2 B­3 B­4 B­5 B­6 B­7 B­8 Cable Colour Yellow Blue/White Red Black Purple Purple/Black Gray Gray/Black White White/Black Green Green/Black Functions Battery Power Control Ignition (ACC) Earth (Ground) Connection Rear Right (+) Rear Right (­) Front Right (+) Front Right (­) Front Left (+) Front Left (­) Rear Left (+) Rear Left (­) 6 English System Connection Receiver unit (front side) PREOUT TO TV TUNER I/F TO NAVIGATION I/F TO 5L-I/F ¶ Front Preout FRONT Audio left output (White) Audio right output (Red) ¶ Rear Preout REAR Audio left output (White) Audio right output (Red) SUB WOOFER ¶ Sub-woofer (Mono) Preout Audio left output (White) Audio right output (Red) Receiver unit (rear side) AV INPUT FM /AM AV OUTPUT ANTENNA AV OUT AV IN POWER TO MONITOR I/F ¶ Audio/Visual Output Visual output (Yellow) Audio left output (White) Audio right output (Red) ¶ Audio/Visual input Visual input (Yellow) Audio left input (White) Audio right input (Red) English 7 Installation Installation for Monitor/Player Unit English Screw (M4X8) (commercially available) Self-tapping screw (commercially available) Firewall or metal support Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Metal mounting strap (commercially available) Accessory 5 Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip). Installation for Receiver unit 1. Attach the installation brackets 9 to the sides of the hideaway unit using the sems bolts 7. Installation brackets (Accessory 9) Sems bolts (M4 × 8 mm) (Accessory 7) 2. Use the tapping screw 8 to secure the hideaway unit to the audio board. Tapping screw (ø4 × 16 mm) (Accessory 8) 8 English Removing Monitor/Player Unit Removing the Hard Rubber Frame 1. Engage the catch pins on the removal tool 6 and remove the two locks on the lower level. Lower the frame and pull it forward as shown in the figure. Accessory 6 Lock Catch 2. When the lower level is removed, remove the upper two locations. The frame can be removed from the top side in the same manner. Removing the Unit 1. Refer to the section and then remove the hard rubber frame. 2. Remove the Hex-head screw with integral washer (M4 × 6) on the back panel. 3. Insert the two removal tools 6 deeply into the slots on each side, as shown. Accessory 6 4. Lower the removal tool toward the bottom, and pull out the unit halfway while pressing towards the inside. Be careful to avoid injury from the catch pins on the removal tool. 5. Pull the unit all the way out with your hands, being careful not to drop it. English 9 Avant l'installation Accessoires 1 ..........1 7 ..........4 2 ..........1 8 ..........4 French 3 ..........1 9 ..........2 4 ..........1 0 ..........1 5 ..........1 6 ..........2 2ATTENTION L'utilisation d'accessoires autres que les accessoires fournis pourrait endommager l'appareil. Assurez-vous d'utiliser les accessoires fournis, indiqués ci-dessus. 10 French Procédure d'installation 1. Afin d'empêcher un court circuit, retirez la clé du contact et déconnectez la batterie -. 2. Effectuez correctement les connexions d'entrée et sortie de chaque appareil. 3. Connectez les câbles de haut-parleur du faisceau de câbles. 4. Connectez les fils du câblage de distribution électrique dans l'ordre suivant : masse, batterie, contact. 5. Connectez le connecteur du câblage de distribution électrique à l'appareil. 6. Installez l'appareil dans votre voiture. 7. Reconnectez la batterie -. 8. Appuyez sur la touche de réinitialisation. 2AVERTISSEMENT Si vous connectez le câble d'allumage (rouge) et le câble de batterie (jaune) au châssis de la voiture (masse), vous risquez de causer un court-circuit qui peut provoquer un incendie. Connectez toujours ces câbles à la source d'alimentation de la boîte à fusible. 2ATTENTION · Si le contact de votre voiture ne dispose pas d'une position ACC, connectez les fils de contact à une source d'alimentation pouvant être activée et désactivée avec la clé de contact. Si vous connectez le fil de contact à une source d'alimentation avec une alimentation de tension constante, comme avec des fils de batterie, la batterie peut mourir. · Si la console a un couvercle, assurez-vous d'installer l'unité de manière à ce que la dalle ne touche pas le couvercle lors de l'ouverture et de la fermeture. · Si le fusible saute, assurez-vous d'abord que les fils ne se touchent pas et n'entraînent pas de court-circuit, puis remplacez le fusible grillé par un fusible neuf de même capacité. · Isolez les câbles non-connectés avec un ruban adhésif en vinyle ou autre matériel similaire. Afin d'empêcher tout court-circuit, ne retirez pas les capuchons présents aux extrémités des fils ou des bornes non connectés. · Connectez les fils d'enceinte correctement aux bornes correspondantes. L'appareil peut être endommagé ou ne pas fonctionner si vous partagez les fils - ou si vous les mettez à la masse sur une partie métallique de la voiture. · Lorsque deux enceintes seulement sont connectées au système, connectez les connecteurs soit aux deux bornes de sortie avant, soit aux deux bornes de sortie arrière (ne mélangez l'avant et l'arrière). Par exemple, si vous connectez le connecteur + de l'enceinte gauche à une borne de sortie avant, ne connectez pas le connecteur - à une borne de sortie arrière. · Après avoir installé l'appareil, vérifiez si les feux de freinage, les indicateurs, les clignotants, etc de la voiture fonctionnent correctement. · Monter l'unité de façon à ce que l'angle de montage soit de 30° ou moins. French 11 Connexion 2AVERTISSEMENT Si vous connectez le câble d'allumage (rouge) et le câble de batterie (jaune) au châssis de la voiture (masse), vous risquez de causer un court-circuit qui peut provoquer un incendie. Connectez toujours ces câbles à la source d'alimentation de la boîte à fusible. L'unité moniteur Ne connectez pas. Batterie 12 French + French Entrée de télécommande de direction (Bleu clair/Jaune) REMO.CONT Faisceau de câbles (Accessoire 3) Connectez à la distribution électrique de commutateur de détection de frein à main du véhicule à l'aide du connecteur de relais fourni. 2ATTENTION Par mesure de sécurité, connecter le câble du détecteur de stationnement. PRK SW D B A Câble de masse (Noir) - (Au châssis de la voiture) ( 5A ) Câble de batterie (Jaune) BATT Câble d'allumage (Rouge) ACC Acces ...